Remote control for electromagnetic locking with remote control for 12V refrigerator

Remote control module with remote control (with batteries) and housing - remote control colour black or white sent at random

Configured and paired - ready to use immediately
The main application of the module is to control the opening of the lock in shop refrigerators. It can also be used as e.g.: light, motor, fan controller and as a remote switch for various other DC and AC devices.

The module can operate in 3 modes :

• Pressing a button on the remote control activates the relay and disconnects it when the button is released.
• A single click on the remote control activates the relay for 5, 10, 15 seconds and then disconnects it.
• One click on the remote control switches the relay on permanently, another click disconnects it.

The relay can operate as a NO contact when a signal is given, or as an NC contact.
The module can operate a maximum of 20 remote controls simultaneously.

Technical data :

• Supply voltage
• Current consumption of the module in standby > 10mA
• Supply voltage 9V-15V DC (optimum supply voltage for long circuit life is 12V DC)
• Switching current max. 250V 10A AC, 30V 10A DC
• Relay operation as NC or NO
• Remote control/receiver range up to 100 m in open field
• Pairing possible with a third-party remote control module
• RF operating frequency 433Mhz learning code EV1527
• RF operating mode superheterodyne reception
• Receiver sensitivity >97dbm (built-in antenna)
• Power supply disconnection does not cause memory loss
• Module dimensions approx. 40x35x25mm, weight 24.7g
• Remote control dimensions approx. 60x35x10mm, weight 18.4g with batteries
• The remote control is powered by 2 x CR2016 button cell batteries (batteries included)

Kit includes :

• Electronic module
• Plastic housing for the module
• Remote control - we send the colour of the remote control randomly - white or black
• Two new batteries installed in the remote control
• Connection instructions ! Polish language

Basic configuration :

The module is pre-configured and paired with the supplied remote control.

1.Pairing a new or another remote control.

The module has the capacity to store and pair up to 20 433Mhz remote controls with learning code EV1527

a) Connect the module to the 12V DC power supply
b) "Click" the programming button on the module. (the LED on the module should light up red)
c) "Click" the button on the paired remote control. (the LED on the module should blink 3 times - this means that the pairing was successful

If for some reason pairing was not successful :

- Disconnect and connect the power supply and repeat the pairing procedure
- Reset module memory and perform pairing procedure

2 Reset the module memory.

a) Connect the module to the 12V DC power supply
b) "Quickly click" the programming button on the module eight times. (The LED on the module should light up red 8 times) - The configuration has been cleared

3. change the batteries in the remote control

- The remote control is supplied with new batteries fitted.
- The remote control is powered by two CR2016 "button" batteries

a) Opening the remote control to change the batteries

- The remote control is closed with plastic clips
- Undermine carefully !!! carefully !!! with a sharp, thin tool in the area of the illustration

4. for advanced users

Timed lock opening setting

The module has the possibility of setting the lock opening time.

- A single click on the remote control triggers the opening of the lock for 5 seconds (setting a longer time is not recommended for electromagnetic locks).

a) Carry out the memory reset procedure from point 2 of the instructions.
b) "fast click" the programming button on the module 4 times - the LED will light up red.
c) "click" the button on the remote control - the LED on the module should blink 4 times (this indicates correct configuration).


In our offer we also have for sale: electric lock with a catch, power supply 12V 2.5A (solid), DC power socket on the cable (matching the plug of the power supply), set JST plug + socket on the cable matching the controller, jumper for the controller, screw for the catch 3.9x13 star, screw M4x40 fixing the lock

We also sell a complete set for the cabinet or refrigerator